Hasbro Neutrona Wand Kit

Do you have multiple Hasbro Neutrona Wands and want to hot swap them with your GPStar Proton Pack? Or do you have a Hasbro Neutrona Wand to use without a Proton Pack? Then this is the kit for you.

A complete Neutrona Wand replacement kit for your Hasbro Neutrona Wand.

Compatible with all Hasbro Neutrona Wands (1984 and Spengler)

Three variants are available.

Stand Alone Variant:  This is a complete electronics replacement for the Hasbro Neutrona Wand. It runs on the original 3x AA batteries, and is intended for when using the wand by itself.

GPStar Variant: This is a complete electronics replacement for the Hasbro Neutrona Wand. It is intended for connecting your Neutrona Wand to a GPStar Proton Pack. Power and data is received by the Proton Pack as they interact with each other.

GPStar Lite Upgrade Variant: If you have a GPStar Lite kit, choose this option to turn your GPStar Lite Kit into a full GPStar Kit. This variant includes the additional Neutrik NL4FXX-S, quick disconnect system and 3/4 loom.

What's Included (Stand Alone Kit Variant): 
For use with a stand alone Hasbro Neutrona Wand.

1x GPStar Neutrona Wand Board
1x GPStar Audio Board (JST-XH 6-pin and Speaker connector pre-soldered)
1x GPStar Power Boost USB-C
1x Wand Cage
1x WIRE #3: Neutrona Wand Power Cable (short)
1x WIRE #19: GPStar Programming Cable
1x WIRE #22: 6pin JST-PH to JST-XH (GPStar Audio <-> Neutrona Wand)

What's Included (GPStar Variant): 
For use when connecting to a GPStar Proton Pack.

1x GPStar Neutrona Wand Board
1x GPStar Audio Board (JST-XH 6-pin and Speaker connector pre-soldered)
1x Wand Cage
3x Wand Handle Connectors (Right/Bottom/Blank variations)
1x Neutrik NL4MP-ST (modded)
1x M3x5 screw
1x WIRE #3 2pin Wand board to wand socket VCC/GND
1x WIRE #4 2pin Wand board to wand socket TX/RX
1x WIRE #22: 6pin JST-PH to JST-XH (GPStar Audio <-> Neutrona Wand)

What's Included (GPStar Lite Upgrade Variant): 
For use when connecting to a GPStar Proton Pack.

1x GPStar Neutrona Wand Board
1x GPStar Audio Board (JST-XH 6-pin and Speaker connector pre-soldered)
1x Wand Cage
3x Wand Handle Connectors (Right/Bottom/Blank variations)
1x Neutrik NL4MP-ST (modded)
1x M3x5 screw
1x WIRE #3 2pin Wand board to wand socket VCC/GND
1x WIRE #4 2pin Wand board to wand socket TX/RX
1x WIRE #22: 6pin JST-PH to JST-XH (GPStar Audio <-> Neutrona Wand)
1x Neutrik NL4FXX-W-S
1x 3/4 Loom
1x CNLinko 4pin Pre-wired quick disconnect. 

Installation Manual download for the Stand Alone Kit:

GPStar_Neutrona Wand Stand Alone_Kit_Installation_Manual (pdf)

Important: If you are upgrading your GPStar Lite Kit into a full GPStar Kit, you will want to choose the GPStar Lite Upgrade Variant.